Fri frakt från 1200kr! Ord. frakt

Monteringsinstruktioner för ben

Nedan finner du monteringsinstruktioner till samtliga av våra ben.

Montering med M8-bult

8 mm bult är ett standard-beslag som passar till en majoritet av möbeltyper.

- Fäst bulten i benets M8-infästning för hand.

- Placera plastbrickan runt bulten och skruva in benet i möbelns förborrade M8-infästning.

Assembly with M8 bolt

The M8 (8mm) bolt is a standard fitting that is compatible with a wide range of furniture types. The correct fittings will be included with the legs. 1. Attach the bolt into the leg by hand and apply the plastic washer over the bolt. 2. Apply the plastic disc over the bolt and mount the leg to the furniture’s pre drilled M8 thread.

Assembly with Universal fitting plate

For furniture without a pre drilled M8 (8 mm) hole, we offer our Universal fitting plate. The correct fittings will be included with the legs. Please ensure that the surface is flat and can take wooden screws. 1. Attach the Universal plate with small screws in the wooden frame/base of your furniture. 2. Simply fasten the leg to the Universal fitting plate by hand.

Assembly of Clas leg

This leg comes with an M8 bolt as well as wooden screws, in order to offer 2 assembling options. M8 (alt 1): If the furniture has M8-threads, use the supplied M8 bolts to mount the legs to the furniture. Wooden screws (alt 2): For all other furniture, use the wooden screws to attach the leg to the wooden frame/base.

Assembly of Hedvig wide

This leg comes with both an M8 bolt as well as wooden screws in order to offer 2 assembling options. M8 (alt 1): If the furniture has pre drilled holes with M8-threads, use the included M8 bolts to attach the legs. Wooden screws (alt 2): For most other furniture, use the smaller screws to attach the legs into the wooden frame of the furniture. Advise: Our leg model Hedvig little works great as a support leg together with Hedvig wide.

Assembly of Hedvig little

This leg comes with an M8 bolt as well as wooden screws, in order to offer 2 assembling options. M8 (alt 1): If the furniture has M8-threads, use the supplied M8 bolts to mount the legs to the furniture. Wooden screws (alt 2): For all other furniture, use the wooden screws to attach the leg to the wooden frame/base. Advise: This leg also works with Hedvig wide as well as Hugo as a center/support leg.

Assembly of Hugo

This leg comes with an M8 bolt as well as wooden screws, in order to offer 2 assembling options. M8 (alt 1): If your furniture has a pre drilled hole with M8-thread (8mm), use a screwdriver to fasten the leg with the M8 bolt. Wooden screws (alt 2): For other furniture - use the wooden screws to attach the leg in the wooden frame or wooden bottom. Advise: Our leg model Hedvig little works great as a support leg together with Hugo.

Assembly of Harald leg

For our Harald legs, there are two different ways of mounting: M8 (alt 1): If your furniture has a pre drilled hole with M8 thread - use the M8 bolt to attach the leg. You can also use some of the wooden screws for extra support. Wooden screws (alt 2): If your furniture does not have a pre drilled hole with M8 thread - use the wooden screws to attach the leg directly to the wooden bottom or wooden frame.

Assembly of Harald table leg

This table leg can be attached to most wooden table tops. 1. Mount directly in the table top with wood screws.

Assembly of Folke tall

1. Place the furniture on its side and make two aligned markings (per leg) above each other, carefully measured 5 cm and 18 cm above the bottom of the furniture to match the holes in the leg. 2. Drill the holes where you have made the marks. Use a drill to fit 8mm bolt. 3. Place the legs over the holes and attach the bolts from the inside of the furniture.

Assembly of Bertil 40 & 100

This leg comes with an M8 bolt as well as wooden screw, in order to offer 2 assembling alternatives. M8 (alt 1): If your furniture has a pre drilled hole with M8-thread (8mm), mount the leg with the M8 bolt. Wooden screws (alt 2): For other furniture - use the wooden screws to attach the leg in the wooden frame or wooden bottom.

Assembly of table leg

Our table legs can be attached to most wooden table tops, as long as they are at least 25 mm thick. 1. Mount directly in the table top with wood screws.

Assembly of Ture

This leg comes with an M8 bolt as well as wooden screws, in order to offer 2 assembling alternatives. M8 (alt 1): If the furniture has an M8-thread, use a screwdriver to fasten the leg with the M8 bolt. Wooden screws (alt 2): For other furniture - use the wooden screws to attach the leg in the wooden frame or wooden bottom.

Note for all assembly options

- Always secure your storage unit against the wall to prevent it from tipping over. - Remember to put felt pads on to protect your floor. - Be cautious not to bend the legs or damage the floor when you turn the furniture over to fit the legs. - If the material in your furniture is porous, it could be necessary to use longer and thicker screws than the ones included to fix the legs properly. - We do not recommend Prettypegs for sofa-beds, since the foldable bed legs usually differ slightly in height comparing with the sofa.

Mounting Instructions for furniture legs

Montering med universalbeslag

Till möbler utan ett förborrat M8 (8 mm) hål, erbjuder vi vårt universalbeslag. Vänligen se till att ytan är platt och går att fästa småskruvar i.

- Skruva fast plattan med de inkluderade skruvarna i hörnen på din möbel.

- Skruva fast benet på kopplingsbeslaget för hand.

Montering av Clas-ben

Till detta ben inkluderas en M8-bult samt träskruvar för att erbjuda två olika sätt att montera.

Alt 1. Om möbeln har förborrade hål med M8-infästningar fästs benet genom att skruva in M8-bulten i infästningen.

Alt 2. För alla andra möbler används träskruvarna för att montera benet i träramen.

Montering av Clas-ben

Montering av Hedvig wide

Till detta ben inkluderas en M8-bult samt träskruvar för att erbjuda två olika sätt att montera.

Alt 1. Om möbeln har förborrade hål med M8-infästningar fästs benet genom att skruva in M8-bulten i infästningen.

Alt 2. För alla andra möbler används träskruvarna för att montera benet i träramen.

Montering av Hedvig little

Till detta ben inkluderas en M8-bult samt träskruvar för att erbjuda två olika sätt att montera.

Alt 1. Om möbeln har förborrade hål med M8-infästningar fästs benet genom att skruva in M8-bulten i infästningen.

Alt 2. För alla andra möbler används träskruvarna för att montera benet i träramen.

Montering av Hugo

Till detta ben inkluderas en M8-bult samt träskruvar för att erbjuda två olika sätt att montera.

Alt 1. Om möbeln har förborrade M8-infästningar fästs benet genom att skruva in M8-bulten i infästningen.

Alt 2. För alla andra möbler används träskruvarna för att montera benet i träramen.

Montering av Harald-ben

Det finns två olika sätt att montera våra Harald-ben:

Alt 1. Om din möbel har ett förborrat hål med M8-infästning, kan du fästa benet med M8-bulten. För extra stöd kan du därutöver använda dig av träskruvarna.

Alt 2. Om din möbel inte har ett förborrat hål med M8-infästning kan du använda träskruvarna för att fästa benet på en plan yta eller träram.

Montering av Harald bordsben

Detta ben kan monteras på de flesta bordsskivor, så länge de kan fästas med skruvar. Skruvar inkluderas.

Montering av folke tall

- Lägg möbeln på sidan, mät och markera 5 cm och 18 cm ovanför möbelns botten. Säkerställ att markeringarna är placerade rakt ovanför varandra.

- Borra där du har gjort markeringarna.

- Vänd möbeln upp och ner och placera benen över borrhålen för att skruva fast dem från insidan.

Montering av Bertil 40 & 100

Till detta ben inkluderas en M8-bult samt träskruvar för att erbjuda två olika sätt att montera.

Alt 1. Om möbeln har förborrade hål med M8-infästningar fästs benet genom att skruva in M8-bulten i infästningen.

Alt 2. För alla andra möbler används träskruvarna för att montera benet i träramen.

Montering av bordsben

Detta ben kan monteras till de flesta bordsskivor, så länge det går att fästa skruv i skivan. Förslagsvis bör skivan vara minst 25 mm tjock. Om skivan är tunnare kan kortare skruv behövas. (20 mm skruv ingår).

Montering av Ture

Till detta ben inkluderas en M8-bult samt träskruvar för att erbjuda två olika sätt att montera.

Alt 1. Om möbeln har förborrade M8-infästningar fästs benet genom att skruva in M8-bulten i infästningen.

Alt 2. För alla andra möbler används träskruvarna för att montera benet i träramen.

Notera för samtliga monteringsalternativ

- Fäst alltid din förvaringsmöbel i väggen för att undvika att den välter

- Som med alla möbelben, var noga med att använda möbeltassar så att golvet inte blir repigt.

- Var försiktig när du vänder möbeln så att inte ben eller golv tar skada. Vi rekommenderar att alltid vara 2 personer för att montera ben på större möbler.

- Vi rekommenderar inte Prettypegs ben för bäddsoffor eftersom benen till den utfällbara sängen oftast inte är utbytbara.

- Om materialet i träramen eller bottenplattan på din möbel verkar poröst, kan det vara nödvändigt att använda längre och grövre skruv än de inkluderade så att benen fäster ordentligt.